1What is torque? (start from zero)

Grab a wrench and try to loosen a stuck bolt. Now slide a length of pipe over the wrench handle and try again — suddenly the bolt turns. Your arm didn't get stronger. What changed is torque: the twisting force around the bolt, and it depends on two things — how hard you push, and how far from the pivot you push.

Torque = Force × Distance from the pivot

Push with 100 newtons (about 10 kg of effort) at the end of a 0.5-meter wrench and you get 50 newton-meters of torque. Same push on a 1-meter cheater bar: 100 newton-meters. Double the handle, double the twist. That's the whole game — and it's why doors have handles far from the hinges, why bike pedals sit at the end of cranks, and why nobody tries to open a jar by gripping the very center of the lid.

Here's a detail that matters: only the perpendicular part of your push counts. Push straight toward the bolt (along the wrench) and you get zero torque — all effort, no twist. Push at 90 degrees to the handle and you get the full effect. That's why the pros reposition the wrench to keep their pull square to the handle.

Torque is also what separates force from twist. Force pushes in a straight line — shoving a box across the floor. Torque rotates around an axis — turning a screwdriver, pedaling a bike, spinning an engine's crankshaft. Every rotating machine in the world, from a ceiling fan to a jet turbine, runs on torque.

bolt Force (100 N) Distance: 0.33 m Torque = 100 N × 0.33 m = 33 Nm Longer handle, same push — more twist
Torque is force times lever arm: 100 N on a 0.33 m wrench gives 33 Nm of twist.

2Meet the torque units

Newton-meter (Nm) — the scientific one

The newton-meter (Nm) is the SI unit: one newton of force applied one meter from the pivot. Car specs outside the US, bicycle components, and torque wrenches in metric countries all use Nm. For a feel of it: 1 Nm is a gentle twist — about what it takes to turn a stiff doorknob, or the torque of a 100-gram apple hanging from the end of a 1-meter stick.

Foot-pound (ft-lb) — the American one

Foot-pounds measure the same thing in imperial: one pound of force one foot from the pivot. US car engines, American torque wrenches, and workshop manuals use ft-lb. One ft-lb equals 1.35581795 Nm — so Nm numbers always run about a third higher than the equivalent ft-lb numbers.

Inch-pound (in-lb) — the small-jobs one

For delicate work — electronics, spark plugs, bicycle parts — foot-pounds are too coarse. Enter the inch-pound: one-twelfth of a ft-lb, equal to 0.112984825 Nm. A torque screwdriver rated 20–100 in-lb covers most small fasteners without stripping them.

Kilogram-force meter (kgf-m) — the old metric one

Before newtons took over, engineers used kilogram-force meters: the torque from a 1 kg weight hanging 1 meter out. It equals 9.80665 Nm (that's just g, 9.80665 m/s², doing the conversion). You'll still find kgf-m in older Japanese and European motorcycle manuals — and it's wonderfully intuitive: 10 kgf-m is what a 10 kg weight does on a 1-meter wrench.

Ounce-inch (oz-in) — the tiny one

At the far small end, ounce-inches rate tiny motors and precision instruments: one oz-in is 0.007061552 Nm. Stepper motors in 3D printers and RC servos are specced in oz-in. Sixteen of them make one in-lb — the imperial system nesting like Russian dolls.

UnitSymbol1 unit equalsYou'll see it in
Newton-meterNm1 Nm (the base unit)Car specs, torque wrenches, bikes (metric world)
Foot-poundft-lb1.35581795 NmUS car engines, American workshop manuals
Inch-poundin-lb0.112984825 NmSmall fasteners, electronics, spark plugs
Kilogram-force meterkgf-m9.80665 NmOlder motorcycle & machinery manuals
Ounce-inchoz-in0.007061552 NmStepper motors, RC servos, precision tools
Quick gut-check: 1 ft-lb ≈ 1.36 Nm, so Nm figures run about a third higher. A "300 ft-lb" truck engine is a "407 Nm" engine — same twist, different ruler.

3Torque vs horsepower — finally explained

Car ads throw both numbers at you — "400 hp, 500 Nm of torque" — and most buyers nod along without knowing which does what. Here's the clean version:

They're locked together by one famous formula:

hp = torque (lb-ft) × RPM ÷ 5,252   ·   kW = torque (Nm) × RPM ÷ 9,549
Worked example: an engine makes 300 lb-ft at 4,000 RPM. Horsepower at that point: 300 × 4,000 ÷ 5,252 = 228.5 hp. The same engine making 300 lb-ft at 5,000 RPM would be making 285.6 hp — same twist, more speed, more power.

That 5,252 is where torque and horsepower curves always cross on a dyno chart — below 5,252 RPM the torque number is bigger, above it the horsepower number wins. It's not magic, just unit conversion wearing a disguise (33,000 ft-lb/min ÷ 2π, if you're curious).

Why does this matter when buying? Diesels and EVs feel strong because of torque, not horsepower. A diesel truck making 1,000 Nm at just 1,600 RPM tows effortlessly, even if its 250 hp seems modest next to a sports car's 400 hp. An electric motor makes peak torque from zero RPM — that's the instant shove you feel in an EV, no revving required. Horsepower tells you about the top end; torque tells you about everyday driving.

Torque vs horsepower across the rev range Torque Horsepower Engine RPM → The curves cross at 5,252 RPM — always. output
Torque peaks early and fades; horsepower keeps climbing with revs. The crossover at 5,252 RPM is pure math.

4Where torque shows up in your daily life

Changing a tire

Lug nuts on most cars want 100–140 Nm (75–100 ft-lb) — check the manual for the exact figure. Too loose and the wheel can work itself free (genuinely dangerous); too tight and you stretch the studs or warp the brake rotor. This is the job torque wrenches were invented for: they click when you hit the spec, so guesswork leaves the building.

Riding a bike

Your legs are a torque machine. Pushing 200 N (about 20 kg of force) on a 170 mm crank arm makes 200 × 0.17 = 34 Nm at the bottom bracket — and that's before the gears multiply it at the wheel. Carbon bike parts are famously torque-sensitive: a seatpost clamp might spec just 5 Nm, and overtightening a $300 handlebar is an expensive lesson in why the small units (Nm, not ft-lb) matter.

Opening jars and doors

A stubborn jar lid needs roughly 3–5 Nm — which is why gripping the lid's edge (maximum radius) works and pinching the center doesn't. Same physics as the wrench: radius is leverage. A door handle sits ~0.8 m from the hinges precisely so a small push makes enough torque to swing a heavy door.

Power tools

An impact driver's headline number is its torque: a good 18 V driver delivers 150–200 Nm, enough to sink long screws into hardwood without pilot holes. Drill specs quote a smaller number (30–60 Nm) because drills are about speed too. And that tiny torque screwdriver for electronics? It lives in the inch-pound world — 20–100 in-lb (2.3–11.3 Nm) — because 50 Nm would shred a laptop screw instantly.

Engines and motors

A family sedan makes roughly 250 Nm (184 ft-lb); a diesel pickup can exceed 1,000 Nm (738 ft-lb). Electric cars cheat beautifully here: an EV motor delivers peak torque from 0 RPM, which is why even a modest EV launches harder than its horsepower suggests. It's also why EVs don't need multi-gear transmissions — the torque is already there, right now.

5How to convert torque units by hand

One multiplier per pair, as always. The two formulas you'll actually use:

Nm = ft-lb × 1.35581795   ·   ft-lb = Nm × 0.737562
Worked example — lug nuts: the manual says 120 Nm, your wrench reads ft-lb. 120 × 0.737562 = 88.5 ft-lb. Set the wrench to 89 and you're good.
Worked example — American engine spec: a truck engine rated 400 ft-lb. In Nm: 400 × 1.35581795 = 542.3 Nm.
Worked example — small fasteners: a bike stem bolt specs 60 in-lb. In Nm: 60 × 0.112984825 = 6.78 Nm. In ft-lb: 60 ÷ 12 = 5 ft-lb — exactly, since 12 in-lb = 1 ft-lb.
Worked example — old motorcycle manual: the spec reads 11 kgf-m. In Nm: 11 × 9.80665 = 107.9 Nm. In ft-lb: 107.9 × 0.737562 = 79.6 ft-lb.
Worked example — stepper motor: a 3D-printer motor rated 40 oz-in. In Nm: 40 × 0.007061552 = 0.282 Nm. In in-lb: 40 ÷ 16 = 2.5 in-lb.

Notice the pattern: convert to Nm first (the base unit), then out to whatever you need. Two multiplications, zero memorized tables — and it's exactly what our converter does behind the scenes.

Everyday torque — from jar lids to truck engines (log scale) Stepper motor0.28 Nm Jar lid4 Nm Bike pedal34 Nm Lug nut120 Nm Sedan engine250 Nm Diesel truck1,000 Nm Four orders of magnitude separate a printer motor from a truck engine — same unit, same physics.
Torque spans everyday life: you apply a few Nm opening jars and hundreds tightening wheels.

6The conversion cheat sheet (Nm ↔ ft-lb and more)

Nmft-lbin-lbTypical use
21.4817.7Electronics screws
53.6944.3Bike seatpost clamp
107.3888.5Small engine bolts
2518.44221Spark plugs
4029.50354Oil drain plug
12088.511,062Lug nuts (typical)
250184.392,213Sedan engine output
500368.784,425Performance car engine
FromToMultiply byMemory aid
ft-lbNm1.35581795"Add a third" (×1.36)
Nmft-lb0.737562"Lose a quarter" (×0.74)
in-lbNm0.11298482512 in-lb = 1 ft-lb, exactly
kgf-mNm9.80665It's just × g
oz-inNm0.00706155216 oz-in = 1 in-lb, exactly

75 mistakes people make with torque

1. Confusing torque with force. "How many pounds of torque?" is a category error — torque is force times distance. 50 lb of force on a 2-foot wrench is 100 ft-lb; the same force on a 6-inch wrench is 25 ft-lb. The force didn't change; the torque did.

2. Writing N/m instead of Nm. Newton-meters (Nm) are torque. Newtons per meter (N/m) is something entirely different — a spring stiffness. The slash changes the meaning completely, and parts catalogs have shipped wrong components over exactly this typo.

3. Ignoring the torque spec. "Good and tight" is not a torque spec. Aluminum threads strip, gaskets crush unevenly, and brake rotors warp when fasteners are tightened by feel. A $30 torque wrench pays for itself the first time it saves a $200 part.

4. Forgetting that lubrication changes everything. Torque specs usually assume clean, dry threads. Oil the threads and the same torque setting clamps much harder — sometimes 20–30% harder — because less effort is lost to friction. Some manuals give separate "dry" and "lubed" specs for exactly this reason.

5. Comparing torque numbers across unit systems. "My engine makes 400" means nothing until you know whether that's Nm or ft-lb — a 400 Nm engine (295 ft-lb) and a 400 ft-lb engine (542 Nm) are very different animals. Always pin the unit to the number.

The golden habit: torque specs exist because "tight enough" is unmeasurable. Look up the spec, set the wrench, listen for the click. Your fasteners — and your wallet — will thank you.

Convert torque in one click — free

Nm ↔ ft-lb ↔ in-lb ↔ kgf-m ↔ oz-in. Type a value, pick your units, get every torque unit at once — no signup, no ads getting in the way.

🔧 Open the Torque Converter

100% free · No account · Private by design

Watch: the wrench turns — rotational force doing the heavy work.

8Frequently asked questions

What is the ft-lb to Nm formula?

Multiply foot-pounds by 1.35581795 to get newton-meters. For example, 100 ft-lb × 1.35581795 = 135.58 Nm. To go the other way, multiply Nm by 0.737562.

What is the difference between torque and horsepower?

Torque is twisting force — how hard the engine twists. Horsepower is how fast it can keep twisting — torque × RPM. They're linked by the formula hp = torque (lb-ft) × RPM ÷ 5,252. Torque gets you moving; horsepower keeps you accelerating at speed.

How much torque do lug nuts need?

Most passenger cars specify 100–140 Nm (75–100 ft-lb) for lug nuts. Always check the owner's manual — too loose and the wheel can work free, too tight and you stretch or snap the studs.

What does 1 Nm feel like?

One newton-meter is a gentle twist — roughly the torque of turning a stiff doorknob, or hanging a 100 g apple from the end of a 1-meter wrench. Opening a tight jar lid takes about 3–5 Nm.

Is torque the same as force?

No. Force pushes in a straight line (newtons); torque twists around an axis (newton-meters). The same force makes more torque the farther from the pivot you apply it — which is why a longer wrench loosens a stubborn bolt more easily.

How many inch-pounds are in a foot-pound?

Exactly 12 inch-pounds make 1 foot-pound, since there are 12 inches in a foot. So 60 in-lb = 5 ft-lb = 6.78 Nm.

Keep exploring

Torque is force with leverage. These related converters cover the quantities it works with:

Related guides

More step-by-step guides on this topic: