1The four quantities (and the water analogy, done honestly)
Every electrical calculation juggles four quantities. Voltage (V, volts) is electrical pressure — how hard the supply pushes. Current (I, amps) is flow — how much charge passes per second. Power (P, watts) is the rate of doing work — pressure × flow. Resistance (R, ohms) is opposition — how hard the load pushes back. The water analogy (voltage = pressure, current = flow rate, resistance = a kink in the hose, power = water actually turning a wheel) is genuinely useful for the first three, and our converter’s job is converting among them without you juggling units.
The master relation for DC and resistive loads is disarmingly simple: P = V × I. A 1,200 W heater on 120 V draws 1,200 ÷ 120 = 10 amps. A 12 V, 5 A car accessory uses 60 W. If you know any two of the four quantities, Ohm’s law (next sections) determines the other two — which is why the converter page carries both a watts↔amps converter and a full Ohm’s law calculator: they’re the same physics wearing two interfaces.
Where people stumble is assuming P = V × I is the whole story. It is — for DC. Mains electricity is AC, and AC adds two wrinkles — power factor and phase configuration — that change the denominator of the conversion. Skipping them is how a “10-amp load” trips a 10-amp breaker.
2DC vs AC: why one formula becomes three
Direct current flows steadily in one direction: batteries, solar panels, USB, car electrics. For DC, current is just watts ÷ volts, full stop — 600 W of solar at 24 V is 25 A, every time. Nothing in DC land complicates that division.
Alternating current reverses direction 50 or 60 times a second, and its voltage and current are waves. For a purely resistive load (heater, incandescent bulb, kettle) the waves rise and fall together, and the simple formula still works: amps = watts ÷ volts. A 2,000 W heater on 230 V draws 8.7 A. But motors, compressors, fluorescent lights and many electronics pull current whose wave is shifted relative to the voltage wave — and shifted waves deliver less useful power per amp. The circuit still carries the full current (and the wires still heat), but the watts delivered are discounted. That discount is the power factor, and it’s why the AC formula is amps = watts ÷ (volts × PF).
Practical consequence: nameplates. A motor stamped “1,000 W” might draw current as if it were a 1,250 W resistive load at PF 0.8. Anyone sizing a generator, inverter or breaker from watts alone, using the DC formula on AC equipment, undersizes by exactly the power factor. Section 3 puts numbers on the discount; the converter asks for the supply type first precisely so the right formula gets used.
3Power factor: the invisible discount on AC power
Power factor (PF) is a number between 0 and 1 that says what fraction of the current flowing actually does work. PF 1.0: all of it (resistive loads). PF 0.9: typical of good-quality modern electronics with corrected supplies. PF 0.8: a working default for motors under load — and the default our converter pre-fills, because it’s the assumption electricians reach for when the nameplate is silent. PF 0.6–0.7: small or lightly loaded motors and cheap LED drivers, where the discount bites hardest.
The size of the bite: 1,000 W at 230 V is 4.35 A at PF 1.0 — but 5.43 A at PF 0.8 and 6.2 A at PF 0.7. The watts (what you’re billed for, roughly) didn’t change; the current (what heats wires and trips breakers) grew by 40%. This is why industrial users are penalised for low power factor and why “volt-amps” (VA) exist as a separate rating: a UPS or generator rated 1,000 VA delivers only 800 W to a PF 0.8 load. When a device’s label gives VA instead of W, it’s telling you the current-side capacity honestly.
If you don’t know a load’s power factor, the nameplate current — when printed — always wins over any calculation. Calculations with PF 0.8 are estimates for planning; nameplate amps are the manufacturer’s measurement for compliance. Use the converter to understand and cross-check, and the nameplate to size.
4Three-phase power and the √3
Industrial and large commercial power arrives as three AC waves offset by a third of a cycle each — three-phase. It runs motors more smoothly and moves more power down thinner wires, which is why factories, EV fast chargers and big HVAC use it. The conversion gains a factor of √3 ≈ 1.732: amps = watts ÷ (√3 × line voltage × PF). A 10 kW three-phase load at 400 V and PF 0.85 draws 10,000 ÷ (1.732 × 400 × 0.85) = 17 A per line — remarkably little current for ten kilowatts, which is the whole point of the system.
Two vocabulary traps guard this formula. The voltage in it is the line-to-line voltage (400 V in Europe, 480/208 V in North American systems, 380–415 V across much of Asia) — not the 230 V line-to-neutral figure. And the result is the current per line, each of the three conductors carrying that same balanced current. Balanced is the assumption: badly unbalanced three-phase loads need per-phase analysis this converter (deliberately) doesn’t pretend to do.
If your world is homes and small workshops, three-phase may never touch you. If a nameplate ever says “3~” or “400 V” or lists a √3-friendly rating, you now know which mode of the converter to choose — and why its answer looks surprisingly small.
5Ohm’s law: the wheel that solves any two-known problem
Ohm’s law proper is one line: V = I × R. Combined with P = V × I it blossoms into twelve formulas — the famous wheel: P = VI = I²R = V²/R; I = P/V = V/R = √(P/R); V = IR = P/I = √(PR); R = V/I = V²/P = P/I². The wheel’s power is practical: electronics works constantly hand you exactly two knowns (a resistor and a supply voltage; a power and a current) and ask for a third. Our Ohm’s law tool takes any two and returns all four quantities.
One worked taste: a heating element measures 20 Ω and runs on 120 V. Current = V ÷ R = 6 A; power = V × I = 720 W (or directly, V²/R = 14,400 ÷ 20 = 720 W — both roads agree, as they must). Run the same element on 240 V and the current doubles to 12 A but the power quadruples to 2,880 W — the square in V²/R made flesh, and the reason running 120 V appliances on 240 V supplies ends in smoke rather than savings.
Resistance itself isn’t constant for many real devices: a cold incandescent filament has a tenth of its hot resistance (hence the inrush that kills bulbs at switch-on), and motor windings behave differently still. Ohm’s law is exact for the quantities at any instant; just remember that “the resistance” of a real load may describe only its operating point.
6Breakers, wires and the 80% rule
Why convert watts to amps at all? Because circuits are protected and wired in amps. Breakers carry amp ratings (15 A, 20 A, 32 A…); cable ampacity is an amp figure; and the safety question “can I plug this in here?” is always an amp question wearing a watt costume. The conversion habit: appliance watts → amps (with PF for motors) → compare against the circuit, keeping the sum of everything on that circuit in view, not just the new arrival.
Then apply the 80% rule: loads that run for three hours or more (“continuous” in the electrical codes) should not exceed 80% of the breaker’s rating — a 20 A circuit carries 16 A continuously, a 15 A circuit 12 A. The space heater example writes itself: 1,500 W at 120 V is 12.5 A — fine alone on a 15 A circuit, but add a 600 W PC (5 A) on the same circuit and the pair sits at 17.5 A of continuous load on a circuit whose continuous budget is 12 A. The breaker may hold for hours before tripping — heat is patient — which is precisely why the rule exists.
7Worked examples: heater, solar array, motor
The heater (resistive, single-phase): 2,000 W at 230 V, PF 1 → 2,000 ÷ 230 = 8.7 A. Comfortable on a 13 A UK socket circuit or a 16 A EU breaker.
The solar array (DC): four 400 W panels in a 24 V battery system — peak 1,600 W ÷ 24 V = 66.7 A of charge current. This is the number that sizes the charge controller (choose 80 A class) and the cable — DC currents at low voltage get big fast, which is why higher-voltage battery banks exist.
The workshop motor (single-phase, PF matters): a 1,500 W motor at 230 V. DC-style maths says 6.5 A. With PF 0.8 the truth is 8.15 A — and the startup surge is several times that again, briefly. Size the breaker from the nameplate and the surge class, not from the naive division.
The EV charger (three-phase): an 11 kW charger at 400 V, PF ~0.95: 11,000 ÷ (1.732 × 400 × 0.95) = 16.7 A per phase — the reason 11 kW home chargers pair with modest 20 A three-phase supplies in Europe, while the same power single-phase at 230 V would demand 48 A.
8Frequently asked questions
How many amps is 1,500 watts?
It depends on voltage and supply type. At 120 V DC or resistive AC: 1,500 ÷ 120 = 12.5 A. At 230 V: 6.5 A. As an AC motor load at PF 0.8 on 230 V: 8.15 A. Always convert with your actual voltage — the same appliance draws half the amps in Europe that it draws in North America.
Why does my answer differ from the appliance nameplate?
Nameplates state the manufacturer's measured or worst-case current, including allowances for voltage variation and operating conditions. Calculations from rated watts and an assumed power factor are estimates. For breaker, wire and generator sizing, the nameplate current is the figure with legal standing — use the converter to understand and cross-check it.
What power factor should I use for a motor?
Nameplate first — many motors print PF or the current directly. If neither is available, 0.8 is the standard planning estimate for a loaded motor; small or lightly loaded motors can run 0.6–0.7, which raises current noticeably. If the calculation decides a breaker size, rounding up a size for motor loads is common electrician practice.
What does the 80% rule mean in practice?
Loads running three hours or more should stay at or below 80% of the breaker's rating: 12 A continuous on a 15 A breaker, 16 A on a 20 A. It exists because sustained current heats connections and breaker mechanisms. Short bursts — a kettle for three minutes — may use the full rating.
Can I plug a 120 V appliance into a 240 V supply with an adapter?
No — a plug adapter changes the shape, not the voltage. On 240 V the appliance draws double the current and dissipates four times the power (P = V²/R), which destroys it quickly and can start a fire. You need a step-down transformer rated for the appliance's watts, and many heating/motor appliances shouldn't be converted at all.
Amps look small on three-phase — is that real?
Yes. Three conductors share the work, and the √3 factor in the formula captures how their waves combine. A 10 kW load at 400 V three-phase draws about 17 A per line at PF 0.85, versus 43.5 A single-phase at 230 V. That's exactly why industry standardised on three-phase for serious power.
Keep exploring
Electrical maths connects to the energy in your walls and your bills:
Convert watts, amps and ohms in seconds
DC, single-phase and three-phase conversions with power factor — plus a full Ohm’s law calculator that solves any two knowns. Free, private, no signup.
⚡ Open the Electrical Converter100% free · No account · Private by design
Related guides
More step-by-step guides on this topic:
